o APCMASTER
o WTI_NPS
Power switch [NONE]: NONE
Information for Cluster Member 1
--------------------------------
Enter name of cluster member [node2]: node2
Looking for host storage1 (may take a few seconds)...
Information about Channel 0
Enter hostname of the cluster member on heartbeat channel 0 \
[node2]: node2
Looking for host storage1 (may take a few seconds)...
Information about Quorum Partitions
Enter Primary Quorum Partition [/dev/raw/raw1]: /dev/raw/raw1
Enter Shadow Quorum Partition [/dev/raw/raw2]: /dev/raw/raw2
Information About the Power Switch That Power Cycles Member ’node2’
Choose one of the following power switches:
o NONE
o RPS10
o BAYTECH
o APCSERIAL
o APCMASTER
o WTI_NPS
Power switch [NONE]: NONE
Cluster name: Development Cluster
Cluster alias IP address: 10.0.0.154
Cluster alias netmask: 255.255.254.0
--------------------
Member 0 Information
--------------------
Name: node1
Primary quorum partition: /dev/raw/raw1
Shadow quorum partition: /dev/raw/raw2
Heartbeat channels: 1
Channel type: net, Name: node1
Power switch IP address or hostname: node1
--------------------
Member 1 Information
--------------------
Name: node2
Primary quorum partition: /dev/raw/raw1
Shadow quorum partition: /dev/raw/raw2
Heartbeat channels: 1
Channel type: net, Name: node2
Save the cluster member information? yes/no [yes]:
Writing to configuration file...done
Configuration information has been saved to /etc/cluster.conf.
----------------------------
Setting up Quorum Partitions
----------------------------
Running cludiskutil -I to initialize the quorum partitions: done
Saving configuration information to quorum partitions: done
Do you wish to allow remote monitoring of the cluster? yes/no \
[yes]: yes
----------------------------------------------------------------
Configuration on this member is complete.
To configure the next member, invoke the following command on that system:
# /sbin/cluconfig --init=/dev/raw/raw1
See the manual to complete the cluster installation
3．配制第二个节点
只需执行 cluconfig --init=/dev/raw/raw1
4．启动Cluster服务
分别在两个节点上执行 service cluster start
您将看到下面的几个Daemon
• cluquorumd — Quorum daemon
• clusvcmgrd — Service manager daemon
• clupowerd — Power daemon
• cluhbd — Heartbeat daemon
• clumibd — Administrative system monitoring daemon
五、建立Cluster应用服务
说明：本次实验只测试了Samba，其他应用服务的建立，请参考RedHat 文档。
.
1．Samba
说明：Samba在cluster的环境下和单机有一些不同，首先是配制文档的改变，不在是/etc/samba/smb.conf，而是/etc/samba/smb.conf.xxxàxxx代表您的共享名字，能够是任何字母。Samba在cluster环境下需要自己的locking目录/var/cache/samba/xxxx
2. 运行/sbin/cluadmin
说明：只需要在其中一个节点执行该命令，当您执行上面的命令您将看到以下输出：
Service name: samba à任何黑色字体代表手工输入接受其默认值
Preferred member [None]:Node1 à这行代表Samba服务将默认在node1上运行。
Relocate when the preferred member joins the cluster (yes/no/?) [no]: yes
User script (e.g., /usr/foo/script or None) [None]:
Status check interval [0]: 10
Do you want to add an IP address to the service (yes/no/?) [no]: yes
IP Address Information
IP address: 10.0.0.10 à这行代表Samba服务运行的IP地址，即windows客户端访问输入的IP地址。
Netmask (e.g. 255.255.255.0 or None) [None]:
Broadcast (e.g. X.Y.Z.255 or None) [None]:
Do you want to (a)dd, (m)odify, (d)elete or (s)how an IP address, or
are you (f)inished adding IP addresses [f]:f
Do you want to add a disk device to the service (yes/no/?) [no]: yes
Disk Device Information
Device special file (e.g., /dev/sdb4): /dev/sdb3
Filesystem type (e.g., ext2, ext3 or None): ext3
Mount point (e.g., /usr/mnt/service1) [None]: /data à这行代表真正共享的存放地。
Mount options (e.g., rw,nosuid,sync): rw,nosuid,sync
Forced unmount support (yes/no/?) [yes]:
Would you like to allow NFS access to this filesystem (yes/no/?)\
[no]: no
Would you like to share to Windows clients (yes/no/?) [no]: yes
You will now be prompted for the Samba configuration:
Samba share name: samba –>这行即windows客户端在网上邻居看到的名字。
The samba config file /etc/samba/smb.conf.samba does not exist.
Would you like a default config file created (yes/no/?) [no]: yes
Successfully created daemon lock directory /var/cache/samba/acct.
Please run ‘mkdir /var/cache/samba/samba‘ on the other cluster member.
Successfully created /etc/samba/smb.conf.samba.
Please remember to make necessary customizations and then copy the file
over to the other cluster member.
文章整理：西部数码--专业提供域名注册、虚拟主机服务
http://www.west263.com
以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息，谢谢!
