我的机器配置如下:p4 1.7 256ddr rtl8139网卡,反复试验了好久终于把8139的网卡驱动程式装好了,现在写出周详的步骤,供大家参考。
1、在realtek的网站上下载驱动程式,网址是:http://www.realtek.com.tw/downloads/downloads1-3.aspx?series=16&Software=True
2、下载下来的驱动程式文档名是:solaris-8139(105).zip,把他拷到硬盘上,然后运行unzip solaris.-8139(105).zip 把该文档解压缩,得到三个文档:
Install 、rtls、Solaris-Readme.txt。
3、用文档管理器运行Install,执行驱动程式的安装。
4、在/etc目录下,创建hostname.rtls0这个文档,/目录下创建reconfigure文档命令为:
touch /etc/hostname.rtls0
touch /reconfigure
5、重新启动,
6、检验端口状态:ifconfig -a
7、配置网卡地址:ifconfig rtls0 10.10.10.10 netmask 255.0.0.0
8、配置端口状态:ifconfig rtls0 up
9、配置端口可用:ifconfig rtls0 plumb

sunsun2003 回复于:2003-05-23 01:14:00
Good!
The machine can't reboot,can it?

doni 回复于:2003-05-23 02:19:09
能reboot

birdmale 回复于:2003-05-23 05:17:57
不明白非的要touch/reconfigure这一步吗?那这又有什么用呢?

race 回复于:2003-05-23 07:36:03
[quote:e098448f75="birdmale"]不明白非的要touch/reconfigure这一步吗?那这又有什么用呢?[/quote:e098448f75]
solaris7以前安装识别新设备都需要这个命令,8以后用devfsadm替代了。

sunsun2003 回复于:2003-05-23 08:07:23
devfsadm -->solaris 8 & 9
devconfig -->solaris 2 though 7

gsea_2000 回复于:2003-05-23 15:24:07
多谢

comcn2 回复于:2003-05-25 01:48:03
[quote:7a5857970e="sunsun2003"]Good!
The machine can't reboot,can it?[/quote:7a5857970e]
用命令reboot

comcn2 回复于:2003-05-25 01:50:20
[quote:85f747bb70="birdmale"]不明白非的要touch/reconfigure这一步吗?那这又有什么用呢?[/quote:85f747bb70]
我也不是很明白,我是参考的realtek公司的安装文档,
实际上这个驱动程式是针对solaris7/solaris8的,但经过试验能够在solaris9下使用

daynight 回复于:2003-05-30 14:53:54
我按照您说的配置了8139,在ifconfig -a 命令能看到rtls0设备,也能够分配IP地址,但是我用LAN其他PC PING SOLARIS却PING不通

显示:

bash-2.03# ping 10.10.10.168
ICMP Host Unreachable from gateway Solaris(10.10.10.10)
for icmp from Solaris (10.10.10.10) to 10.10.10.168

请问这个如何解决?谢谢。。。

daynight 回复于:2003-05-30 14:56:10
#ifconfig rtls0

rtls0: flags=10000849<UP,POINTOPOINT,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.10.10.10--->127.0.0.1 netmask ffffff00
ether .......

wein 回复于:2003-05-30 16:45:33
既然网卡都已装上了,假如只有这一块网卡
建议使用sys-unconfig重新配置

我昨天刚装好的8139,很easy

daynight 回复于:2003-05-30 19:43:12
恩,我最后还是用sys-unconfig搞定的,没办法。。。

comcn2 回复于:2003-05-31 12:41:55
[quote:57849e518f="daynight"]我按照您说的配置了8139,在ifconfig -a 命令能看到rtls0设备,也能够分配IP地址,但是我用LAN其他PC PING SOLARIS却PING不通

显示:

bash-2.03# ping 10.10.10.168
ICMP Host Unreachable from gateway Sola..........[/quote:57849e518f]


您有没有做下面这个步骤:
ifconfig rtls0 up
ifconfig rtls0 plumb

醒木 回复于:2003-05-31 12:58:43
[quote:b6e5817ccb="daynight"]恩,我最后还是用sys-unconfig搞定的,没办法。。。[/quote:b6e5817ccb]

我也同意用这种方法,那种手工配置的方法太高难度,太容易出错

daynight 回复于:2003-05-31 13:42:00
[quote:7bc077a350="comcn2"]


您有没有做下面这个步骤:
ifconfig rtls0 up
ifconfig rtls0 plumb[/quote:7bc077a350]

我是严格按照您写的步骤做的,呵呵~~~



原来的:
rtls0: flags=10000849<UP,[color=red:7bc077a350]POINTOPOINT[/color:7bc077a350],RUNNING,MULTICAST,IPv4> mtu 1500 index 2

用sys-unconfig以后发现有点不同:
变成了[color=red:7bc077a350]BROADCAST[/color:7bc077a350],就能够了
不知道这一项要如何用手工配置实现?

wein 回复于:2003-05-31 21:49:55
用sys-unconfig方法配置后和手工配置做了下对比
没觉得有什么不同
不知道为什么手工就不成功

gongdehua 回复于:2003-06-01 03:01:06
8139那卡我到现在一直没有配好,改天非得重新再试试!谢谢各位了

pandalinux 回复于:2003-06-01 07:32:49
[quote:1cb686f891="comcn2"]我的机器配置如下:p4 1.7 256ddr rtl8139网卡,反复试验了好久终于把8139的网卡驱动程式装好了,现在写出周详的步骤,供大家参考。
1、在realtek的网站上下载驱动程式,网址是:http://www.realtek.com.tw/downl..........[/quote:1cb686f891]

文章整理:西部数码--专业提供域名注册虚拟主机服务
http://www.west263.com
以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息,谢谢!